Heating & Cooling

Hotplates · Baths · Chillers · Circulators · Ovens

Temperature control from a bench hotplate to a process chiller — chosen by the range you need to hold and whether you are heating the sample or the vessel around it.

Authorized distribution·Freight coordinated on floor-standing units·Capacity confirmed at your setpoint
Popular Configurations

Start With a Common Setup

Six of the most-specified units. The full range, with filters, is below.

5 Gallon Pail Heating Blanket5 Gallon Pail Heating Blanket$203.40Powerblanket · wax & glycerinDry Block Heater, 12-PlaceDry Block Heater, 12-Place$211.50Aluminium block · 15–77 mmDigital Laboratory HotplateDigital Laboratory Hotplate$329.80Globe Scientific · to 380/550°CDigital Hotplate StirrerDigital Hotplate Stirrer$448.50Globe Scientific · glass-ceramic topiCL-030L Incubator, 30 LiCL-030L Incubator, 30 L$1,227.60LW Scientific · digital PID to 65°CCORIO CD-200F CirculatorCORIO CD-200F Circulator$4,415.00JULABO · −20°C to 150°C
Buying Guide

How to Specify Heating & Cooling

Open only what you need. Whether the heat goes into the sample or the vessel around it sets the equipment class.

Choose by what you are controlling direct heat · jacket or loop · drying · hold warm

Heat the sample directly

The heat source touches the vessel — a plate, an aluminium block, or a bath. Fastest to set up, and the right answer whenever the sample sits in a tube, flask or beaker on the bench.

Control a jacket or an external loop

A circulator pumps fluid through a jacketed reactor, a condenser or a cold trap. This is what you buy when the temperature has to be held on a whole process, not a single vessel — and where the useful range runs well below and above what a bath can reach.

Dry, evaporate and drive off solvent

Removing mass rather than holding a setpoint. Forced-air ovens for straightforward drying, vacuum ovens when the material cannot take the temperature that atmospheric drying would need.

Hold warm, or heat a drum

Long-duration warmth rather than a process step — culture and sample incubation on the bench, and blanket heaters that bring a pail or a 55-gallon drum back to a workable viscosity.

Temperature range by equipment class published figures for the models stocked here
Class Range How it works Choose it for
Dry block heater Ambient to ~150°C Fixed aluminium block, drilled for one tube size Incubating tubes at a setpoint; no water to top up or contaminate.
Hotplate / hotplate stirrer To 380°C or 550°C Glass-ceramic or ceramic-coated top Open-vessel heating on the bench, with or without magnetic stirring.
Circulating water bath Ambient to ~100°C Digital PID, 20 L reservoir Even, gentle heat around multiple vessels at once.
Laboratory incubator Ambient to 65°C Digital PID, chamber Culture work and warm storage over hours or days.
Forced-air / vacuum oven Ambient upward, vacuum optional Stainless chamber; vacuum models pull the boiling point down Drying solids — vacuum when heat would damage the material.
Recirculating chiller −75°C to +40°C depending on model Closed loop, pumped to your equipment Removing heat continuously — condensers, rotary evaporators, reactors.
Refrigerated bath circulator −20°C to 150°C · −35°C to 200°C · −55°C to 200°C Heats and cools; internal bath plus external loop One unit covering both directions on a jacketed vessel.
Dynamic temperature control −50°C to 250°C Pilot ONE controller, near-zero bath volume Fast, programmed ramps across a wide span on process reactors.
Have us size it for you fluid, heat load and facility power

Send the fluid, the volume, the target temperature and the heat load, plus your facility voltage and phase. We confirm the unit has real capacity at your setpoint before you order — large chillers and dynamic temperature systems frequently need three-phase power.

Do I need a bath circulator or a recirculating chiller?
A recirculating chiller only removes heat. It pumps coolant in a closed loop to a condenser, a rotary evaporator or a reactor jacket and holds it cold, which is all most solvent-recovery and condenser duty ever needs. A refrigerated bath circulator both heats and cools, has an open bath you can immerse vessels in, and drives an external loop as well — so it covers a process that has to be taken up as well as down. If your temperature only ever goes one direction, the chiller is the cheaper and simpler machine.
What temperature range should I actually specify?
Specify the range your process needs at the vessel, then allow headroom at both ends, because a unit working at the very edge of its span runs continuously and controls poorly. Cooling capacity also falls as the setpoint drops — a chiller rated to a low temperature delivers far fewer watts down there than it does near ambient. Tell us the fluid, the volume, the target temperature and the heat load, and we will confirm the unit has real capacity at your setpoint rather than just a number on the datasheet.
Why choose a vacuum oven over a forced-air oven?
Vacuum lowers the boiling point, so a vacuum oven removes solvent or moisture at a much lower temperature than an atmospheric oven would need. That matters when the material degrades, oxidises or discolours with heat. A forced-air oven is simpler, faster to load and cheaper to run, and it is the better choice for routine drying of anything thermally stable.
Can a hotplate stirrer replace a water bath?
For a single vessel, often yes — a hotplate stirrer heats and agitates in one footprint, and a glass-ceramic top reaches temperatures no water bath can. A bath still wins when you need several vessels held at an identical, gentle temperature, or when direct contact with a hot plate would create hot spots in a viscous or heat-sensitive sample. Water baths also cap out near boiling, which is a limit rather than a drawback for most biological work.
What do I need to tell you to get the right unit?
Five things settle almost every specification: the temperature range at the sample, the volume or heat load, whether you are heating, cooling or both, the fluid involved, and your facility power — voltage, phase and available amperage. Large chillers and dynamic temperature control systems in particular often need three-phase, and that is worth confirming before an order rather than on the loading dock.

85 products